Product Description
This drive is compatible with AC input voltages of 80-132VAC (1-phase), 80-264VAC (1-phase), and 80-264VAC (3-phase). It delivers a continuous output current of 17.0 A and a continuous power output of 3.0 kW, while also featuring Safe Torque-Off (STO) functionality, overvoltage protection, and short-circuit current protection.
The 2097-V33PR6-LM Kinetix drive can be integrated with MP and TL series servo motors and actuators, as well as various Allen-Bradley control and interface products, including PanelView Operator Terminals (HMIs), 1734 Point I/O remote I/O modules, MicroLogix 1400 Programmable Logic Controllers (PLCs), and CompactLogix and ControlLogix Programmable Automation Controllers (PACs).
For proper installation, the 2097-V33PR6-LM requires a minimum mounting clearance of 3 millimeters (0.12 inches) on both sides and 25 millimeters (1 inch) on the top and bottom to ensure adequate airflow and ventilation. Note that these minimum clearances may need to be increased depending on any installed accessories.
To minimize electrical noise, implementing bonding by connecting metal chassis, assemblies, frames, shields, and enclosures is recommended to reduce electromagnetic interference (EMI). Installing the drive on a zinc-plated or paint-free steel subpanel can further improve bonding. It is crucial to exercise caution during bonding to avoid creating unintentional return paths for high-frequency energy, which could damage other electronic components.
During installation, the protective covers on the connector pins should not be removed to prevent foreign material from causing short circuits and damaging the module. Additionally, circuit shield devices should not be used on the output of this AC drive as isolating disconnect switches or motor surge protection devices, as the PWM waveform is incompatible with their intended sine wave operation and could lead to device failure. For optimal performance of the 2097-V33PR6-LM, it is essential to select properly synchronized modules that meet relevant codes, including any requirements for branch circuit protection. Assessing the available short-circuit current and ensuring it remains below the circuit breaker's short-circuit current rating is also important.
Is Your Device Showing These Signs?
The Allen Bradley 2097-V33PR6-LM Kinetix 3 component commonly experiences issues such as resolver signal degradation, resulting in inaccurate positioning and velocity control. Field failures often stem from corrupted firmware requiring a re-flash via Ethernet/IP. We address power supply faults, specifically DC bus undervoltage, by repairing or replacing capacitors and rectifiers. Overcurrent faults, triggered by shorted motor windings or excessive load, necessitate IGBT testing and replacement. Communication errors on the SERCOS interface are resolved through cable inspection, connector repair, and communication parameter verification.
Technical specifications
Input Voltage: 80-132VAC, 1-Phase; 80-264VAC, 1-Phase; 80-264VAC, 3-Phase
Part Number/Catalog No.: 2097-V33PR6-LM
Brand: Allen-Bradley
Manufacturer: Rockwell Automation
Product Bulletin: 2097 Kinetix 300 Drives
Product Description: 2097 Kinetix 300 Single Axis Ethernet I/P Drives
Input Frequency: 48…62 Hz
Main AC input current, Nom (rms):120/240V input, single-phase: 24.0 A
240V input, three-phase: 13.9 AMax inrush (0-pk):120/240V input: 5.65 A
240V input: 11.3 AControl power back-up input voltage: 20…26V DC
Control power back-up input current, nominal: 500 mA
Control power back-up input current, max. inrush: 30 A
Continuous output current (rms): 12.0 A
Continuous output current (0-pk): 17.0 A
Peak output current (rms): 36.0 A
Peak output current (0-pk): 50.9 A
Continuous power output: 3.00 kW
Safe Torque-Off: Yes
120 Volts Doubler Mode: No
Continuous Output Current (0-peak): 17.0 Amperes
Integrated AC (EMC) Line Filter: No
Power Rating: 3.0 kWatts
Dimensions: 9.37 x 7.29 x 3.06 in (238 x 185.1 x 12.38 mm)
Weight: 4.2 lbs (1.9 kg)
Our Repair Process for the
2097-V33PR6-LM
Our repair process for the Allen Bradley 2097-V33PR6-LM Kinetix 3 component begins with a comprehensive diagnostic evaluation to pinpoint the root cause of the failure. Resolver signal degradation, a common issue, is addressed through resolver replacement or signal conditioning circuit repair. Firmware corruption necessitates a complete re-flash via Ethernet/IP. Power supply faults, such as DC bus undervoltage, are rectified by repairing or replacing faulty capacitors and rectifiers. Overcurrent faults require thorough IGBT testing, and replacement is performed as needed, along with motor winding and load inspection. Communication errors on the SERCOS interface are resolved through meticulous cable inspection, connector repair, and verification of all communication parameters.
Your Guarantee: Warranty & Lifetime Support
Your satisfaction is our top priority, and we confidently stand behind the quality of our repairs. That's why every repair service is covered by our comprehensive 24-month warranty. Furthermore, we offer lifetime phone support – if you have questions or need assistance related to our repair down the road, we're here to help. Our service commitment is straightforward: we guarantee our work, and if you're not satisfied, we will make it right. Learn More about our Repair process.
Comprehensive Repairs You Can Depend On
We take immense pride in the quality and reliability of our work. Our process goes beyond simply fixing the immediate problem. We perform a comprehensive inspection of your main board (or other equipment) and proactively replace components known to be failure-prone or showing signs of potential future failure. Before any item is returned, it undergoes rigorous functional testing to ensure it meets performance specifications and operates flawlessly. Visit our main Repair Services page to learn more.
Save Significantly
Our primary goal is to save you hundreds, or even thousands, of dollars compared to the cost of new equipment replacement. By repairing existing components, we provide an economical solution that is also eco-friendly. At Roc Industrial, our commitment to integrity and community drives our consistent growth and ensures you receive a reliable, cost-effective solution.
Please Note: Roc Industrial operates as an independent service provider and is not an authorized distributor for the manufacturers or brands mentioned. Consequently, the original manufacturer's warranty is not applicable to items repaired or sold by us. Roc Industrial provides its own 2-year warranty on all repair services performed.
Buying Options
To receive a quote within 2 hours, please provide us with the details of your requirements. Our team will promptly review your request and send you a custom offer.
Ships from Rochester, NY