Product Description
The Allen-Bradley 2098-IPD-HV220 is a High Voltage Ultra5000 Intelligent Positioning Drive, characterized by its full programmability, high performance, and a modern Digital Signal Processing (DSP) based power section. It utilizes ANSI C programmed motion commands and boasts an optimized design with high-speed position capturing capabilities, achieving a latency of less than 1.0μs.
Here are its key specifications:
Continuous Power Output: 22 kW at 480 Volts AC
Weight: Approximately 32 pounds
Dimensions: 9.00 x 15.43 x 14.28 inches
Optically Isolated I/O: 16 inputs, 7 outputs, and 1 normally open relay output
Input Voltage: 230 to 480 Volt Root Means Square (RMS) three-phase AC
Nominal Input Current: 28 A (RMS) AC input current
Output Current:
66.5A (RMS) peak output current
33.2A (RMS) continuous output current
94A (0-peak) intermittent output current
47A (0-peak) continuous output current
Bus Capacitance: 1880µF
Internal Shunt Resistance: 20Ω
Bus Overvoltage Protection: 810 Volt DC
Maximum Power Dissipation: 600 Watts (with a dissipative shunt)
Memory: 512 Kb of flash memory and 23 Kb of non-volatile SRAM for storage
Communication Ports: Two RS-485, RS-232, or RS-422 serial ports, supporting communication rates of 1200, 2400, 4800, 9600, 19200, and 38400 bps
Operating Environment: Industrial environments, 0 to 55 degrees Celsius operating temperature (32 to 131 degrees Fahrenheit), and 5% to 95% non-condensing relative humidity
Is Your Device Showing These Signs?
The Allen Bradley 2098-IPD-HV220 commonly experiences issues related to power supply failures, resulting in operational downtime. Resolve communication errors stemming from corrupted firmware or incorrect Ethernet/IP configurations. Address motor performance degradation caused by faulty IGBTs or resolver feedback problems. Correct overheating issues due to inadequate heat sink contact or excessive ambient temperatures. Rectify drive tripping caused by overcurrent faults, short circuits, or improper motor parameter settings.
Technical specifications
Manufacturer: Rockwell Automation
Brand: Allen-Bradley
Part Number/Catalog No.: 2098-IPD-HV220
Series: Ultra 5000 Drives
Output Current (Intermittent): 94 Amps (0-peak)
Output Current (Continuous): 47 Amps (0-peak)
Auxiliary Power Supply: Yes
Nominal Input Current (AC): 28 Amps Root Means Square
Input Frequency (AC): 47-63 Hz
Input Voltage (AC): 230-480 Voltage Root Means Square (Three Phase)
Our Repair Process for the
2098-IPD-HV220
Our repair process for the Allen Bradley 2098-IPD-HV220 begins with a comprehensive diagnostic evaluation to pinpoint the root cause of the reported issue, whether it be power supply failure, communication errors, motor performance degradation, overheating, or drive tripping. We then proceed with component-level repairs, which include replacing faulty IGBTs, rectifying resolver feedback problems, and correcting heat sink issues. Firmware is updated or reconfigured to resolve communication errors, and Ethernet/IP settings are verified for proper network integration. Motor parameters are meticulously adjusted to eliminate overcurrent faults and short circuits. Post-repair, the drive undergoes rigorous testing under load to ensure it meets or exceeds original performance specifications, minimizing future operational downtime.
Your Guarantee: Warranty & Lifetime Support
Your satisfaction is our top priority, and we confidently stand behind the quality of our repairs. That's why every repair service is covered by our comprehensive 24-month warranty. Furthermore, we offer lifetime phone support – if you have questions or need assistance related to our repair down the road, we're here to help. Our service commitment is straightforward: we guarantee our work, and if you're not satisfied, we will make it right. Learn More about our Repair process.
Comprehensive Repairs You Can Depend On
We take immense pride in the quality and reliability of our work. Our process goes beyond simply fixing the immediate problem. We perform a comprehensive inspection of your main board (or other equipment) and proactively replace components known to be failure-prone or showing signs of potential future failure. Before any item is returned, it undergoes rigorous functional testing to ensure it meets performance specifications and operates flawlessly. Visit our main Repair Services page to learn more.
Save Significantly
Our primary goal is to save you hundreds, or even thousands, of dollars compared to the cost of new equipment replacement. By repairing existing components, we provide an economical solution that is also eco-friendly. At Roc Industrial, our commitment to integrity and community drives our consistent growth and ensures you receive a reliable, cost-effective solution.
Please Note: Roc Industrial operates as an independent service provider and is not an authorized distributor for the manufacturers or brands mentioned. Consequently, the original manufacturer's warranty is not applicable to items repaired or sold by us. Roc Industrial provides its own 2-year warranty on all repair services performed.
Buying Options
To receive a quote within 2 hours, please provide us with the details of your requirements. Our team will promptly review your request and send you a custom offer.
Ships from Rochester, NY